Tips & Terms

AFUE – Annual Fuel Utilization Efficiency which is a measure of a gas furnace’s efficiency in converting fuel to energy. The higher the AFUE rating, the more efficient the unit. For example: A rating of 90 means that approximately 90 % of the fuel is used to provide warmth to your home, while the remaining 10 percent escapes as exhaust. We offer only 90% furnaces from Trane® and Lennox, the most efficient for our customers. Some models actually achieve 95% efficiency.

BTU – British Thermal Unit. This is the amount of heat it takes to raise one pound of water one degree Fahrenheit. For your home, it represents the measure of heat given off when fuel is burned for heating or the measure of heat extracted from your home for cooling.

CFM – Cubic Feet Per Minute. CFM is a standard measurement of airflow. A typical system requires 400 CFM per ton of air conditioning.

Capacity – The output or producing ability of a piece of cooling or heating equipment. Cooling and heating capacities are measured in BTUs.

Comfort-R Airflow System – An exclusive feature of a high efficiency home comfort system from Trane®. This method of ramping airflow gives you greater humidity control in cooling and provides warmer air during heating start up.

Compressor – The heart of an air conditioning or heat pump system. It is part of the outdoor unit and pumps refrigerant in order to meet the cooling requirements of the system.

Condenser Coil or Outdoor Coil – In an air conditioner, the coil dissipates heat from the refrigerant, changing the refrigerant from vapor to liquid. In a heat pump system, it absorbs heat from the outdoors.

Damper – Found in ductwork, this movable plate opens and closes to control airflow. Dampers can be used to balance airflow in a duct system. They are also used in zoning to regulate airflow to certain rooms.

Ductwork – Pipes or channels that carry air throughout your home. In a home comfort system, ductwork is critical to performance ­ in fact, it’s as critical as the equipment.

Evaporator Coil or Indoor Coil – The other half of your air conditioning system located inside your home in the indoor unit. This is where the refrigerant evaporates as it absorbs heat from the air that passes over the coil.

Gas Furnace Heat Exchanger – Located in the furnace, the heat exchanger transfers heat to the surrounding air, which is then pumped throughout your home.

HSPF – Heating Seasonal Performance Factor. This rating is used in measuring the heating efficiency of a heat pump. The higher HSFP number, the more efficient the unit.

Package Unit – A heating and cooling system contained in one outdoor unit. A package unit is typically installed either: beside, on top of the home, or sometimes in the attic.

Refrigerant – A chemical that produces a refrigerating effect while expanding and vaporizing. Most residential air conditioning systems contain R-22 refrigerant. R-22 is regulated by international controls under the Montreal Protocol and in the United States by the Environmental Protection Agency. It is scheduled to be in production until the year 2020. It’s used in approximately 95 percent of air conditioning equipment manufactured in the U.S. today. R-22 is being replaced by R-14.

SEER – Seasonal Energy Efficiency Ratio. SEER is a measure of cooling efficiency for air conditioners and heat pumps. The higher the SEER numbers the more energy efficient the unit. The government’s minimum SEER rating is 10. (It’s similar to comparing miles per gallon in automobiles.)

SEET – Seasonal Extreme Environmental Test Lab. This is Trane®‘s torture chamber for heating and air conditioning systems, where five years of service are condensed into 16 torturous weeks. If a product doesn’t make it through our SEET lab, it’s not manufactured. We push our equipment to extremes because we’d rather test them in our lab than in your home.

Split System – The combination of an outdoor unit (air conditioner or heat pump) with an indoor unit (furnace or air handler). Split systems must be matched for optimum efficiency.

Thermostat – A thermostat consists of a series of sensors and relays that monitor and control the functions of a heating and cooling system.

Ton – A unit of measurement used for determining cooling capacity. One ton is the equivalent of 12,000 BTUs per hour.

Zoning – A method of dividing a home into different comfort zones so each zone can be independently controlled depending on use and need.


Knueve & Sons provides heating, cooling, plumbing, and bath remodeling services to residential and commercial customers in Bluffton, Columbus Grove, Continental, Defiance, Delphos, Elida, Findlay, Fort Jennings, Kalida, Leipsic, McComb, Ottawa, Paulding, Shawnee, Van Wert, and surrounding Ohio communities. Visit our service area page to learn more about how we can service your home. Contact us at 419-532-3699 or request service online.

Trane Comfort Specialist badge

Pin It on Pinterest

419-532-3699 419-532-369924-Hour Emergency Service Available!

Service Financing